Standverwaltung
Option auswählen

Behringer Srl

Via Gualco 4, 16165 Genova
Italy
Telephone +39 010 8309103
Fax +39 010 8309183
info@behringer.it

Submit your contact details

Provide your contact details to the exhibitor. Optionally, you may also add a personal message.

Please log in

You must be logged in to send the contact request.

An error has occurred

Please check your internet connection or try again later.

Message has been sent

Your message to the exhibitor was sent successfully.

Hall map

MEDICA 2021 hall map (Hall 11): stand G40

Fairground map

MEDICA 2021 fairground map: Hall 11

Our range of products

Product categories

  • 01  Imaging and diagnostics / medical equipment and devices
  • 01.09  Hospital equipment, care equipment
  • 01.09.14  Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Our products

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Semi-automatic distributor module ECO/7 PLUS - 9 BAR

Medium/high flow rate manifold module for medical gases, available both with automatic exchange and manual reset function and fully automatic. Both versions are available with pressure transducer or pressure switch. Consists of a two-stage pressure reducer and guarantees a continuous supply with high pressure stability. The outlet connection is designed for welded pipes with a diameter of 22 mm. Its maximum flow rate for nitrogen at 9 bar outlet pressure is 90 Nm³/h, 1500Nl/min. The manifold also features a steel plate and a lightweight and easy-to-fasten white polycarbonate cover.

More Less

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Cylinder pressure regulator according to TRD 451

The cylinder pressure regulator suitable for medical gases is used to regulate the gas pressure down to the line or system pressure. A double manometer fitted to the outlet of the gas cylinder indicates the high and low pressure.The maximum inlet pressure is 200 bar, the outlet pressure can be set to a maximum of 12 bar.The inlet connection is matched to the gas in question. The outlet is provided with a weld-on pipe connection with 6 mm Ø.The maximum nitrogen flow at 12 bar outlet pressure is 90 Nm³/h or 1500 Nl/min.

More Less

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

2nd stage unit with integrated zone valve

The unit consists of two chemically nickel-plated cast brass parts: one for the regulator housing and one for the zone valve.The regulator housing has two decompression lines with two EURO/A regulators connected as a bypass via four ball valves, two at the inlet and two at the outlet. The system pressure upstream of the regulator is measured with a pressure gauge.The zone valve at the outlet of the regulator housing has a ball shut-off valve at the inlet. In addition, there is a device for a proximity sensor to determine the valve status (open/closed), an emergency socket and a pressure gauge with electrical contacts.All valve seats and pressure gauges are equipped with check valves to prevent gas leakage during maintenance.The inlet and outlet connections are made using a 16 mm Ø weld-on pipe. In addition, the unit has a block that can be physically separated.When the 2nd stage unit with integrated zone valve is installed outside the station in the filter room, it can be used as a shut-off module. It thus performs the function of a shut-off valve, a regulator module and a zone shut-off valve in the event of a fire. This saves considerable time and effort during installation.

More Less

About us

Company portrait

The know-how acquired over many years of experience enables Behringer to always provide the most cost effective solutions, based on advanced technology, top quality and excellent performance. The company operates with a growing international focus in the following sectors: medical gas equipment, welding devices, devices for pure gases, gas equipment for food use and devices for torching. Of note, our newly formed Service department dedicated to medical installations.